Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Access Control Cost in Round Rock?
Gate access control in Round Rock typically runs $450 to $1,400 for a residential driveway gate, and $1,800 to $5,500 or more for a commercial access system, depending on what’s being added or replaced. A simple keypad or remote receiver swap often lands near the low end. A full operator replacement with new control board, safety sensors, and entry hardware pushes toward the high end. Every job is priced per job by a free written estimate, so the number you see on paper is the number you pay.
If your gate isn’t responding, the issue could be the access hardware, the operator, or the wiring between them. Call (888) 853-0490 and we’ll get a dedicated gate technician out to sort it. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Key Takeaways
- Residential gate access control in Round Rock runs roughly $450-$1,400; commercial systems $1,800-$5,500+.
- Keypads, remotes, and intercoms sit at the lower end; full control board and operator work at the higher end.
- Texas heat and sun exposure are the biggest silent factors on Round Rock control boards and outdoor keypads.
- We work on your brand – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Free estimates, and the written estimate sets the final price.
Gate Access Control Cost Breakdown (2026)
Here’s how the pieces of a typical access-control job price out in the Round Rock market. These are estimate ranges – the written estimate after we look at your gate sets the final number.
| Item | Typical Cost Range | Notes |
|---|---|---|
| Keypad or entry pad replacement (residential) | $180 – $450 | Wired or battery keypads; includes programming |
| Remote receiver or transmitter setup | $120 – $350 | Extra remotes and receiver boards |
| Safety sensor / photo-eye replacement | $200 – $500 | Pair of sensors plus alignment and wiring check |
| Control board replacement | $350 – $850 | Diagnosis, new board, reprogramming |
| Access-control wiring repair | $250 – $900 | Depends on run length and where the fault sits |
| Intercom or video entry station (residential) | $450 – $1,200 | Unit plus wiring and integration with the operator |
| Full residential operator replacement with access hardware | $1,400 – $3,200 | Motor, control board, sensors, and entry hardware |
| Commercial access-control system (add or replace) | $1,800 – $5,500+ | DoorKing-class systems, multiple entry points, loop or card readers |
| New gate installation with access control | Quoted per job | Sized on site – gate, operator, wiring, hardware |
What pushes a job up: commercial-grade operators and multi-point systems, long underground wire runs, replacing a discontinued control board where the wiring has to be adapted, and gates where the access hardware and the operator are both tired. What keeps it down: a single failing component, existing wiring that’s still good, and a brand we already know inside out. We service nine brands across the residential and commercial spectrum, so brand recognition isn’t the variable – the condition of your gate is. Our technicians have up to 11 years of experience on both electric and manual systems.
What Affects Gate Access Control Pricing in Round Rock
- Residential vs. commercial duty. A homeowner’s driveway gate with a keypad is a different animal from a commercial access system with card readers, vehicle loops, and multiple operators. Commercial work prices higher because there’s more of it, and the hardware is heavier-rated for daily traffic.
- Which brand you’re running. We work on your brand – from DIY-friendly Mighty Mule and Ghost Controls to LiftMaster, Linear, and Viking at the mid-range, up to FAAC, BFT, DoorKing, and Elite on the commercial side. Parts availability and complexity vary by brand, and so does the labor to integrate new access hardware with an existing operator.
- Texas heat and sun. Round Rock summers bake outdoor control boards, keypads, and sensor housings. A control board that lives in direct afternoon sun ages faster than one in a shaded enclosure, and a failing board is one of the most common reasons a gate stops responding to a keypad or remote. That sun exposure is a real cost driver when it’s time to replace the electronics.
- Wiring condition and run length. Access control is only as good as the wire carrying the signal. Long driveway runs, older direct-burial cable, and rodent damage all add labor. A fault that’s easy to find costs less than one buried mid-run.
- Whether the operator is part of the problem. Sometimes the access hardware is fine and the operator is failing. Sometimes it’s the reverse. Diagnosis matters – and it’s part of the free estimate.
- Property layout and gate weight. A wide, heavy slide gate on a commercial entrance needs an operator and access hardware rated for that load and cycle count. A residential swing gate doesn’t. That sizing gap shows up in the price.
How to Save on Gate Access Control
The biggest savings come from catching a failing component before it takes the whole system down. A $200 sensor replacement is a lot cheaper than a control board that fails because the system kept operating on a bad sensor.
- Get a diagnosis before you replace. A gate that won’t respond to a keypad isn’t automatically a dead control board. It could be the keypad, the receiver, the wiring, or the operator. Knowing which one saves you from paying for parts you didn’t need.
- Ask about battery vs. wired keypads. On a residential gate where running wire is hard, a quality battery keypad can cut installation labor noticeably.
- Keep the operator you have if it’s sound. If the motor is healthy, new access hardware and sensors on the existing operator is the cheaper path. If the operator is on its way out, replacing it alongside the access hardware is usually better value than doing the two jobs separately.
- Get a free written estimate. Call (888) 853-0490 and we’ll price the job up front. No surprises.
For a deeper look at what’s involved across the full range of gate work, our gate repair round rock service covers diagnosis, repair, electric systems, and new installation under one roof.
Why Call a Dedicated Gate Specialist?
Access control is electrical. It lives in motors, control boards, safety sensors, and the wiring between all of it. A generalist or a garage-door company that also touches gates will get the hinges right and struggle with the electronics. We’re a gate specialist, full stop – repair, electric systems, and installation. When a gate is beyond saving, we install the new one rather than handing you off to a second contractor. And because we’re brand-agnostic across nine manufacturers, our recommendation is based on what’s best for your gate, not on a single-brand dealership incentive.
Whether it’s a residential driveway gate or a commercial access system, we get you back up and running. Insured & bonded, with a free estimate and a written price you can see before anyone touches your gate. Gate customers in Round Rock call us because the access-control side is the part most other companies can’t handle.
FAQs – Gate Access Control Cost
How much does gate access control cost in Round Rock?
Residential gate access control in Round Rock typically runs $450 to $1,400, while commercial access systems run $1,800 to $5,500 or more. The exact price depends on which components you’re adding or replacing and the condition of the wiring. Call (888) 853-0490 for a free written estimate.
Is it cheaper to repair or replace my gate’s access system?
Repair is almost always cheaper when the operator is healthy and one component is failing – a keypad, receiver, or sensor swap stays in the $120-$500 range versus a full operator replacement at $1,400+. Replacement makes more sense when the operator is on its way out, the control board is discontinued, or the system no longer meets what the property needs. Call (888) 853-0490 and we’ll tell you honestly which side of that line you’re on.
Why won’t my gate respond to the keypad or remote?
In most cases it’s one of three things: a failing keypad or receiver, a bad safety sensor, or a wiring fault – not the operator itself. Diagnosis is the first step, and it’s part of the free estimate. Call (888) 853-0490 to get a technician out.
Do you work on my gate operator brand?
Yes. We work on nine brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – spanning residential DIY-friendly systems up to commercial-grade operators. That range means the brand on your gate isn’t a roadblock. Call (888) 853-0490 for a free estimate.
Can you come today?
Yes, same-day service is often available. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (888) 853-0490 for an exact quote – estimates are free.
Get a Free Gate Access Control Estimate in Round Rock
Access control pricing in Round Rock comes down to what’s failing and what your gate actually needs. We work on your brand, we handle the electrical side – motors, control boards, safety sensors, and access hardware – and we install new gates when repair no longer makes sense. Electric or manual, residential or commercial, we handle both. Insured & bonded, with a free written estimate and a price set per job before work starts.
Call (888) 853-0490 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Pricing reflects the Round Rock market as of 2026. Gate Repair Round Rock offers free estimates – call (888) 853-0490.
Written by the team at Gate Repair Round Rock.
What Our Customers Say
"We had a hydraulic arm leaking fluid onto the driveway. Replaced, cleaned up the stain as best he could, and it's been dry for months."
- Rashad Nash"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
- Paige Schaefer"Photo eye was misaligned so the gate refused to close after dark. Ten minute fix. He also cleaned the lens and pointed out that the sprinkler head was spraying it every morning, which is why it kept happening."
- Ryan Vaughn